ObjectiveTo explore the effectiveness of a new point contact pedicle navigation template (referred to as “new navigation template” for simplicity) in assisting screw implantation in scoliosis correction surgery. MethodsTwenty-five patients with scoliosis, who met the selection criteria between February 2020 and February 2023, were selected as the trial group. During the scoliosis correction surgery, the three-dimensional printed new navigation template was used to assist in screw implantation. Fifty patients who had undergone screw implantation with traditional free-hand implantation technique between February 2019 and February 2023 were matched according to the inclusion and exclusion criteria as the control group. There was no significant difference between the two groups (P>0.05) in terms of gender, age, disease duration, Cobb angle on the coronal plane of the main curve, Cobb angle at the Bending position of the main curve, the position of the apical vertebrae of the main curve, and the number of vertebrae with the pedicle diameter lower than 50%/75% of the national average, and the number of patients whose apical vertebrae rotation exceeded 40°. The number of fused vertebrae, the number of pedicle screws, the time of pedicle screw implantation, implant bleeding, fluoroscopy frequency, and manual diversion frequency were compared between the two groups. The occurrence of implant complications was observed. Based on the X-ray films at 2 weeks after operation, the pedicle screw grading was recorded, the accuracy of the implant and the main curvature correction rate were calculated. ResultsBoth groups successfully completed the surgeries. Among them, the trial group implanted 267 screws and fused 177 vertebrae; the control group implanted 523 screws and fused 358 vertebrae. There was no significant difference between the two groups (P>0.05) in terms of the number of fused vertebrae, the number of pedicle screws, the pedicle screw grading and accuracy, and the main curvature correction rate. However, the time of pedicle screw implantation, implant bleeding, fluoroscopy frequency, and manual diversion frequency were significantly lower in trial group than in control group (P<0.05). There was no complications related to screws implantation during or after operation in the two groups. ConclusionThe new navigation template is suitable for all kinds of deformed vertebral lamina and articular process, which not only improves the accuracy of screw implantation, but also reduces the difficulty of operation, shortens the operation time, and reduces intraoperative bleeding.
ObjectiveTo summarize the research progress of several three-dimensional (3-D) printing scaffold materials in bone tissue engineering.
MethodThe recent domestic and international articles about 3-D printing scaffold materials were reviewed and summarized.
ResultsCompared with conventional manufacturing methods, 3-D printing has distinctive advantages, such as enhancing the controllability of the structure and increasing the productivity. In addition to the traditional metal and ceramic scaffolds, 3-D printing scaffolds carrying seeding cells and tissue factors as well as scaffolds filling particular drugs for special need have been paid more and more attention.
ConclusionsThe development of 3-D printing porous scaffolds have revealed new perspectives in bone repairing. But it is still at the initial stage, more basic and clinical researches are still needed.
Objective To explore the effect of NaOH on the surface morphology of three-dimensional (3D) printed poly-L-lactic acid (PLLA) mesh scaffolds. Methods The 3D printed PLLA mesh scaffolds were prepared by fused deposition molding technology, then the scaffold surfaces were etched with the NaOH solution. The concentrations of NaOH solution were 0.01, 0.1, 0.5, 1.0, and 3.0 mol/L, and the treatment time was 1, 3, 6, 9, and 12 hours, respectively. There were a total of 25 concentration and time combinations. After treatment, the microstructure, energy spectrum, roughness, hydrophilicity, compressive strength, as well as cell adhesion and proliferation of the scaffolds were observed. The untreated scaffolds were used as a normal control. Results 3D printed PLLA mesh scaffolds were successfully prepared by using fused deposition molding technology. After NaOH etching treatment, a rough or micro porous structure was constructed on the surface of the scaffold, and with the increase of NaOH concentration and treatment time, the size and density of the pores increased. The characterization of the scaffolds by energy dispersive spectroscopy showed that the crystal contains two elements, Na and O. The surface roughness of NaOH treated scaffolds significantly increased (P<0.05) and the contact angle significantly decreased (P<0.05) compared to untreated scaffolds. There was no significant difference in compressive strength between the untreated scaffolds and treated scaffolds under conditions of 0.1 mol/L/12 h and 1.0 mol/L/3 h (P>0.05), while the compression strength of the other treated scaffolds were significantly lower than that of the untreated scaffolds (P<0.05). After co-culturing the cells with the scaffold, NaOH treatment resulted in an increase in the number of cells on the surface of the scaffold and the spreading area of individual cells, and more synapses extending from adherent cells. Conclusion NaOH treatment is beneficial for increasing the surface hydrophilicity and cell adhesion of 3D printed PLLA mesh scaffolds.
Objective To investigate the effectiveness of sacroiliac screw implantation assisted by three-dimensional (3D) printed faceted honeycomb guide plate in the treatment of posterior pelvic ring fracture. Methods The clinical data of 40 patients with posterior pelvic ring fractures treated with sacroiliac screw implantation between December 2019 and December 2022 were retrospectively analyzed. Among them, 18 cases were treated with sacroiliac screws fixation assisted by 3D printed faceted honeycomb guide plate (guide plate group), and 22 cases were treated with sacroiliac screws percutaneously fixation under fluoroscopy (conventional group). There was no significant difference in baseline data (P>0.05) such as gender, age, time from injury to operation, and Dennis classification between the two groups. The implantation time, frequency of C-arm X-ray fluoroscopy, frequency of guide pin adjustment of each sacroiliac screw, and postoperative complications and bone healing were recorded. Majeed score was used to evaluate the functional recovery at 6 months after operation, and CT was used to observe whether the screw penetrated the bone cortex. The deviation between the virtual position and the actual position of the screw tip, the sacral foramen, and the screw entry point was measured on the sagittal CT images of the guide plate group. Results The number of screws implanted in S1 and S2 vertebral bodies was 14 and 16 respectively in the guide plate group, and 17 and 18 respectively in the conventional group. The implantation time of each sacroiliac screw, the frequency of C-arm X-ray fluoroscopy, and the frequency of guide pin adjustment in S1, S2, and all vertebrae in the guide plate group were significantly less than those in the conventional group (P<0.05). Patients in both groups were followed up 8-48 months, with an average of 19.7 months. There was no incision infection, screw displacement, or internal fixation loosening in both groups. Callus growth was observed in all patients at 12 weeks after operation, and bone healing was achieved in all patients. The healing time ranged from 12 to 24 weeks, with an average of 15.7 weeks. No sacroiliac screw penetrated the bone cortex in the guide plate group; 2 patients in the conventional group had sacroiliac screws penetrating the bone cortex without damaging blood vessels or nerves. In the guide plate group, the deviation between the virtual position and the actual position of the screw tip, the sacral foramen, and the screw entry point were (2.91±1.01), (2.10±0.74), and (1.67±0.70) mm, respectively, with an average deviation of (2.19±1.22) mm. There was no significant difference in Majeed function evaluation between the two groups at 6 months after operation (P>0.05). Conclusion The application of 3D printed faceted honeycomb guide plate in sacroiliac screw implantation for posterior pelvic ring fracture can shorten the screw implantation time, reduce the frequency of fluoroscopy and guide pin adjustment, and reduce the risk of screw penetration through the bone cortex.
Objective To explore the application effect of 3D printed heart models in the training of young cardiac surgeons, and evaluate their application value in surgical simulation and skill improvement. MethodsEight young cardiac surgeons were selected form West China Hospital as the trainees. Before training, the Hands-On Surgical Training-Congenital Heart Surgery (HOST-CHS) operation scores of the 8 cardiac surgeons were obtained after operating on 2 pig heart models of ventricular septal defect (VSD). Subsequently, simulation training was conducted on a 3D printed peri-membrane VSD heart model for 6 weeks, once a week. After the training, all trainees completed 2 pig heart VSD repair surgeries. The improvement of doctors’ skills was evaluated through survey questionnaires, HOST-CHS scores, and operation time after training. ResultsBefore the training, the average HOST-CHS score of the 8 trainees was 52.2±6.3 points, and the average time for VSD repair was 54.7±7.1 min. During the 6-week simulation training using 3D printed models, the total score of HOST-CHS for the 8 trainees gradually increased (P<0.001), and the time required to complete VSD repair was shortened (P<0.001). The trainees had the most significant improvement in scores of surgical cognition and protective awareness. The survey results showed that trainees were generally very satisfied with the effectiveness of 3D model simulation training. Conclusion The 3D printed VSD model demonstrates significant application advantages in the training of young cardiac surgeons. By providing highly realistic anatomical structures, 3D models can effectively enhance surgeons’ surgical skills. It is suggested to further promote the application of 3D printing technology in medical education, providing strong support for cultivating high-quality cardiac surgeons.
ObjectiveTo explore the effectiveness of excision and reconstruction of bone tumor by using operation guide plate made by variety of three-dimensional (3-D) printing techniques, and to compare the advantages and disadvantages of different 3-D printing techniques in the manufacture and application of operation guide plate.
MethodsBetween September 2012 and January 2014, 31 patients with bone tumor underwent excision and reconstruction of bone tumor by using operation guide plate. There were 19 males and 12 females, aged 6-67 years (median, 23 years). The disease duration ranged from 15 days to 12 months (median, 2 months). There were 13 cases of malignant tumor and 18 cases of benign tumor. The tumor located in the femur (9 cases), the spine (7 cases), the tibia (6 cases), the pelvis (5 cases), the humerus (3 cases), and the fibula (1 case). Four kinds of 3-D printing technique were used in processing operation guide plate:fused deposition modeling (FDM) in 9 cases, stereo lithography appearance (SLA) in 14 cases, 3-D printing technique in 5 cases, and selective laser sintering (SLS) in 3 cases; the materials included ABS resin, photosensitive resin, plaster, and aluminum alloy, respectively. Before operation, all patients underwent thin layer CT scanning (0.625 mm) in addition to conventional imaging. The data were collected for tumor resection design, and operation guide plate was designed on the basis of excision plan. Preoperatively, the operation guide plates were made by 3-D printing equipment. After sterilization, the guide plates were used for excision and reconstruction of bone tumor. The time of plates processing cycle was recorded to analyse the efficiency of 4 kinds of 3-D printing techniques. The time for design and operation and intraoperative fluoroscopy frequency were recorded. Twenty-eight patients underwent similar operations during the same period as the control group.
ResultsThe processing time of operation guide plate was (19.3±6.5) hours in FDM, (5.2±1.3) hours in SLA, (8.6±1.9) hours in 3-D printing technique, and (51.7±12.9) hours in SLS. The preoperative design and operation guide plate were successfully made, which was used for excision and reconstruction of bone tumor in 31 cases. Except 3 failures (operation guide plate fracture), the resection and reconstruction operations followed the preoperative design in the other 28 cases. The patients had longer design time, shorter operation time, and less fluoroscopy frequency than the patients of the control group, showing significant differences (P<0.05). The follow-up time was 1-12 months (mean, 3.7 months). Postoperative X-ray and CT showed complete tumor resection and stable reconstruction.
Conclusion3-D printing operation guide plates are well adapted to the requirements of individual operation for bone tumor resection and reconstruction. The 4 kinds of 3-D printing techniques have their own advantages and should be chosen according to the need of operation.
The incidence of valvular heart disease (VHD) increases with age, and its principal therapy is valve replacement. However, in recent years, the emergence of transcatheter interventions has changed the traditional therapy, making high-risk patients of surgery see dawn of hope. 3D printing technology has developed rapidly since it was applied to the medical field in 1990. Moreover, it has been widely applied in many surgical majors via refined reduction technology. However, the application of 3D printing technology in cardiovascular surgery is still in the preliminary stage, especially in the field of VHD. This article aims to review basic principles of 3D printing technology, its advantages in the therapy of VHD, and its current status of clinical application. Furthermore, this article elaborates current problems and looks forward to the future development direction.
Objective To explore the effectiveness of computer-aided technology in the treatment of primary elbow osteoarthritis combined with stiffness under arthroscopy. Methods The clinical data of 32 patients with primary elbow osteoarthritis combined with stiffness between June 2018 and December 2020 were retrospectively analyzed. There were 22 males and 10 females with an average age of 53.4 years (range, 31-71 years). X-ray film and three-dimensional CT examinations showed osteophytes of varying degrees in the elbow joint. Loose bodies existed in 16 cases, and there were 7 cases combined with ulnar nerve entrapment syndrome. The median symptom duration was 2.5 years (range, 3 months to 22.5 years). The location of bone impingement from 0° extension to 140° flexion of the elbow joint was simulated by computer-aided technology before operation and a three-dimensional printed model was used to visualize the amount and scope of impinging osteophytes removal from the anterior and posterior elbow joint to accurately guide the operation. Meanwhile, the effect of elbow joint release and impinging osteophytes removal was examined visually under arthroscopy. The visual analogue scale (VAS) score, Mayo elbow performance score (MEPS), and elbow range of motion (extension, flexion, extension and flexion) were compared between before and after operation to evaluate elbow function. Results The mean operation time was 108 minutes (range, 50-160 minutes). All 32 patients were followed up 9-18 months with an average of 12.5 months. There was no other complication such as infection, nervous system injury, joint cavity effusion, and heterotopic ossification, except 2 cases with postoperative joint contracture at 3 weeks after operation due to the failure to persist in regular functional exercises. Loose bodies of elbow and impinging osteophytes were removed completely for all patients, and functional recovery was satisfactory. At last follow-up, VAS score, MEPS score, extension, flexion, flexion and extension range of motion significantly improved when compared with preoperative ones (P<0.05). Conclusion Arthroscopic treatment of primary elbow osteoarthritis combined with stiffness using computer-aided technology can significantly reduce pain, achieve satisfactory functional recovery and reliable effectiveness.
ObjectiveTo prepare bionic spinal cord scaffold of collagen-heparin sulfate by three-dimensional (3-D) printing, and provide a cell carrier for tissue engineering in the treatment of spinal cord injury.
MethodsCollagen-heparin sulfate hydrogel was prepared firstly, and 3-D printer was used to make bionic spinal cord scaffold. The structure was observed to measure its porosity. The scaffold was immersed in simulated body fluid to observe the quality change. The neural stem cells (NSCs) were isolated from fetal rat brain cortex of 14 days pregnant Sprague-Dawley rats and cultured. The experiment was divided into 2 groups: in group A, the scaffold was co-cultured with rat NSCs for 7 days to observe cell adhesion and morphological changes;in group B, the NSCs were cultured in 24 wells culture plate precoating with poly lysine. MTT assay was used to detect the cell viability, and immunofluorescence staining was used to identify the differentiation of NSCs.
ResultsBionic spinal cord scaffold was fabricated by 3-D printer successfully. Scanning electron microscope (SEM) observation revealed the micro porous structure with parallel and longitudinal arrangements and with the porosity of 90.25%±2.15%. in vitro, the value of pH was not changed obviously. After 8 weeks, the scaffold was completely degraded, and it met the requirements of tissue engineering scaffolds. MTT results showed that there was no significant difference in absorbence (A) value between 2 groups at 1, 3, and 7 days after culture (P>0.05). There were a lot of NSCs with reticular nerve fiber under light microscope in 2 groups;the cells adhered to the scaffold, and axons growth and neurosphere formation were observed in group A under SEM at 7 days after culture. The immunofluorescence staining observation showed that NSCs could differentiated into neurons and glial cells in 2 groups;the differentiation rate was 29.60%±2.68% in group A and was 10.90%±2.13% in group B, showing significant difference (t=17.30, P=0.01).
ConclusionThe collagen-heparin sulfate scaffold by 3-D-printed has good biocompatibility and biological properties. It can promote the proliferation and differentiation of NSCs, and can used as a neural tissue engineered scaffold with great value of research and application.
