Lower extremity movement is a complex and large range of limb movement. Arterial stents implanted in lower extremity are prone to complex mechanical deformation, so the stent is required to have high comprehensive mechanical properties. In order to evaluate the mechanical property of different stents, in this paper, finite element method was used to simulate and compare the mechanical properties of six nitinol stents (Absolute Pro, Complete SE, Lifestent, Protégé EverFlex, Pulsar-35 and New) under different deformation modes, such as radial compression, axial compression/tension, bending and torsion, and the radial support performance of the stents was verified by experiments. The results showed that the comprehensive performance of New stent was better than other stents. Among which the radial support performance was higher than Absolute Pro and Pulsar-35 stent, the axial support performance was better than Complete SE, Lifestent and Protégé EverFlex stent, the flexibility was superior to Protégé Everflex stent, and the torsion performance was better than Complete SE, Lifestent and Protégé Everflex stent. The TTR2 type radial support force tester was used to test the radial support performance of 6 types, and the finite element analysis results were verified. The mechanical properties of the stent are closely related to the structural size. The result provides a reference for choosing a suitable stent according to the needs of the diseased location in clinical applications.
To investigate the effects of postoperative fusion implantation on the mesoscopic biomechanical properties of vertebrae and bone tissue osteogenesis in idiopathic scoliosis, a macroscopic finite element model of the postoperative fusion device was developed, and a mesoscopic model of the bone unit was developed using the Saint Venant sub-model approach. To simulate human physiological conditions, the differences in biomechanical properties between macroscopic cortical bone and mesoscopic bone units under the same boundary conditions were studied, and the effects of fusion implantation on bone tissue growth at the mesoscopic scale were analyzed. The results showed that the stresses in the mesoscopic structure of the lumbar spine increased compared to the macroscopic structure, and the mesoscopic stress in this case is 2.606 to 5.958 times of the macroscopic stress; the stresses in the upper bone unit of the fusion device were greater than those in the lower part; the average stresses in the upper vertebral body end surfaces were ranked in the order of right, left, posterior and anterior; the stresses in the lower vertebral body were ranked in the order of left, posterior, right and anterior; and rotation was the condition with the greatest stress value in the bone unit. It is hypothesized that bone tissue osteogenesis is better on the upper face of the fusion than on the lower face, and that bone tissue growth rate on the upper face is in the order of right, left, posterior, and anterior; while on the lower face, it is in the order of left, posterior, right, and anterior; and that patients’ constant rotational movements after surgery is conducive to bone growth. The results of the study may provide a theoretical basis for the design of surgical protocols and optimization of fusion devices for idiopathic scoliosis.
【Abstract】 Objective To investigate the feasibil ity of applying enzymatic method to prepare decellularizedporcine aorta and to evaluate its biomechanical properties, immunogenicity and cell compatibil ity. Methods 0.1% trypsin- 0.01% EDTA was appl ied to extract cells from porcine aorta under 37 continuously vibrating condition and its histology and microstructure were observed. The thickness, stress-strain curve, ultimate tension stress (UTS) and strain of failure (SOF) were compared before and after decellularization for 48, 96 and 120 hours under uniaxial tensile tests, respectively. The histological change was observed at 1, 3 and 6 weeks after the decellularized tissue was implanted subcutaneously in 3 dogs. According to the HE stains and a semi-quantitative Wakitani grading method, gross changes, category and amounts of infiltrated cells and neo-capillaries were compared between pre- and post-decellularization of porcine aortae. Endothel ial cells from canine external jugular vein were seeded onto the decellularized patches to observe the cell compatibil ity. Results Microscopy and electron microscopies examination identified that cell components was completely removed from the fresh porcine aorta and Masson’ strichrome showed that the structure of matrix (fibrins) was maintained intact at 96 hours using the decellularization method. There were no significant differences in the thickness, UTS and SOF between before and after decellularization (P gt; 0.05). However, The UTS values showed a decrease tendency and SOF showed an increase tendency. The stress-strain curve also verified a decrease tendency in mechanical intensity and an increase one in ductil ity after decellularization. After implanting the acellularized matrix subcutaneously in canine, moderately lymphocyte infiltration was seen at the 1st week and the infiltration was replaced by fibroblasts accompanied by neocapillary formation at the 6th week. A semi-quantity histological evaluation showed that there were differences in gross observation, category and the numbers of the infiltrated cells between decellularized and non-decellularized tissues（P lt; 0.05). A cell monolayer was identified by HE staining and scanning electron microscopywhen the endothel ial cells were seeded onto the inner luminal surface of the scaffold, al igned at the same direction on the whole. Conclusion The decellularized porcine aortic scaffold, prepared by trypsin-EDTA extraction under continuously vibrating condition, could meet the requirements of tissue-engineering graft in biomechanical properties, immunogenicity and cell compatibil ity.
The effect of parasitic ions on the results of ultraviolet A (UVA) cross-linking in iontophoresis was still not clear. In this work, the porcine sclera was cross-linked by riboflavin lactate Ringer’s solution (group A) and riboflavin normal saline (group B) in vitro, respectively. The concentration of parasitic ions in the solution was calculated. In addition, the average fluorescence intensity, penetration depth and concentration after the introduction of riboflavin and the mechanical properties of cross-linked sclera tissue were measured. The ranges of diffusion coefficient of the two solutions were also calculated, respectively. The results showed that more kinds of parasitic ions were detected in group A compared with group B, while the average fluorescence intensity, penetration depth and concentration of riboflavin and scleral elastic modulus in group B were significantly higher than those in group A when the penetration time was 10 minutes. Besides, the diffusion coefficient of riboflavin in group B was about 1.5 times larger than that in group A. The results suggested that the species of parasitic ions has a great impact on the permeability of riboflavin, and affects the mechanical properties of cross-linked sclera. The above results could provide a reference for improving the efficiency of riboflavin introduction and optimizing the formula of riboflavin in iontophoresis scleral cross-linking.
In order to understand how the biomechanical properties of rabbit cornea change over time after corneal ablation, 21 healthy adult rabbits were used in this study, with the left eye as experimental side and the right eye as the control side. Firstly, a lamellar knife was used to remove a portion of the anterior corneal surface tissue (30%~50% of the original corneal thickness) from the left eye of each rabbit, as an animal model simulating corneal refractive surgery. Secondly, postoperative experimental rabbits were kept for one, three, or six months until being euthanized. Strip specimens were produced using their corneas in vitro to perform a uniaxial tensile test with an average loading-unloading rate of approximately 0.16 mm/s. Finally, the visco-hyperelastic material constitutive model was used to fit the data. The results showed that there was a significant difference in the viscoelastic parameters of the corneas between the experimental and the control eyes at the first and third postoperative months. There was a difference in tangential modulus between the experimental and the control eyes at strain levels of 0.02 and 0.05 at the third postoperative month. There was no significant difference in biomechanical parameters between the experimental and the control eyes at the sixth postoperative month. These results indicate that compared with the control eyes, the biomechanical properties of the experimental eyes vary over postoperative time. At the third postoperative month, the ratio of corneal tangential modulus between the experimental and the control eyes significantly increased, and then decreased. This work lays a preliminary foundation for understanding the biomechanical properties of the cornea after corneal refractive surgery based on rapid testing data obtained clinically.
Objective To investigate the biological and biomechanical characteristics of acellular porcine aortic valve with dye mediated photo oxidation so that a new and better bioprosthetic valve materials can be obtained. Methods Thirty porcine aortic valves were divided into three groups with random number table. Acellular valves (n=10) were stabilized by dye mediated photo oxidation in dye mediated photo oxidation group; acellular valves (n=10) were stabilized by glutaraldehyde in glutaraldehyde group; and acellular valves (n=10) were acellularized only in acellular valves group. Thickness, appearance, histology, water content, shrinkage temperature, breaking strength and soluble protein level of acellular porcine aortic in three groups were tested respectively. Results There were light blue, soft, flexible and unshrinking valves in dye mediated photo oxidation group. Compared to valves in glutaraldehyde group, valves in dye mediated photo oxidation group had lighter thickness（0.26±0.09mm vs. 0.38±0.08mm，Plt;0.05）, more water content（86.30%±4.03% vs. 71.10%±3.23%，Plt;0.05）, and lower shrinkage temperature （76.30±0.70℃ vs. 87.70±0.30℃，Plt;0.05）; while these indexes had no statistically significant differences compared to those in acellular valves group. At the same time, compared to valves in acellular valves group, valves in dye mediated photo oxidation group had more breaking strength（17.33±2.65 mPa vs. 9.11±0.95 mPa，Plt;0.05） and lower soluble protein level（0.039%±0.013% vs. 0.107%±0.024%，Plt;0.05）; while these indexes had no statistically significant differences compared to those in glutaraldehyde group. Conclusion Acellular porcine aortic valve stabilized by dye mediated photo oxidation has nice biological and biomechanical characteristics.
Biodegradable stents (BDSs) are the milestone in percutaneous coronary intervention(PCI). Biodegradable polymeric stents have received widespread attention due to their good biocompatibility, moderate degradation rate and degradation products without toxicity or side effects. However, due to the defects in mechanical properties of polymer materials, the clinical application of polymeric BDS has been affected. In this paper, the BDS geometric configuration design was analyzed to improve the radial strength, flexibility and reduce the shrinkage rate of biodegradable polymeric stents. And from the aspects of numerical simulation, in vitro experiment and animal experiment, the configuration design and mechanical properties of biodegradable polymeric stents were introduced in detail in order to provide further references for the development of biodegradable polymeric stents.
Focusing on the poor mechanical strength of porous bioceramics bone scaffold, and taking into account of the good mechanical properties of biodegradable magnesium alloy, we proposed a novel method to fabricate magnesium alloy/bioceramics composite bone scaffold with stereolithography double channels. Firstly, a scaffold structure without mutually connected double channels was designed. Then, an optimized bioceramics scaffold was fabricated according to stereolithography and gel-casing. Molten AZ31 magnesium alloy was perfused into the secondary channel of scaffold by low-pressure casting, and magnesium alloy/bioceramics composite bone scaffold was obtained when magnesium alloy was solidified. The compression test showed that the strength of bioceramics scaffold with only one channel and without magnesium alloy was (9.76±0.64) MPa, while the strength of magnesium alloy/bioceramics composite scaffold with double channels was (17.25±0.88) MPa. It can be concluded that the magnesium alloy/bioceramics composite is obviously able to improve the scaffold strength.
The current finite element analysis of vascular stent expansion does not take into account the effect of the stent release pose on the expansion results. In this study, stent and vessel model were established by Pro/E. Five kinds of finite element assembly models were constructed by ABAQUS, including 0 degree without eccentricity model, 3 degree without eccentricity model, 5 degree without eccentricity model, 0 degree axial eccentricity model and 0 degree radial eccentricity model. These models were divided into two groups of experiments for numerical simulation with respect to angle and eccentricity. The mechanical parameters such as foreshortening rate, radial recoil rate and dog boning rate were calculated. The influence of angle and eccentricity on the numerical simulation was obtained by comparative analysis. Calculation results showed that the residual stenosis rates were 38.3%, 38.4%, 38.4%, 35.7% and 38.2% respectively for the 5 models. The results indicate that the pose has less effect on the numerical simulation results so that it can be neglected when the accuracy of the result is not highly required, and the basic model as 0 degree without eccentricity model is feasible for numerical simulation.
Coronary artery diseases (CAD) have always been serious threats to human health. The measurement, constitutive modeling, and analysis of mechanical properties of the blood vessel wall can provide a tool for disease diagnosis, stent implantation, and artificial artery design. The vessel wall has both active and passive mechanical properties. The passive mechanical properties are mainly determined by elastic and collagen fibers, and the active mechanical properties are determined by the contraction of vascular smooth muscle cells (VSMC). Substantial studies have shown that, the two-layer model of the vessel wall can feature the mechanical properties well, and the circumferential, axial and radial strain and stress are of great significance in arterial wall mechanics. This study reviewed recent investigations of mechanical properties of the vessel wall. Challenges and opportunities in this area are discussed relevant to the clinical treatment of coronary artery diseases.
